The
best grain management system from DMC features Calc-U-Dri*,
Stir-Ator and Grain Flow. These components convert your drying
bin into the ultimate automatic in-bin continuous flow drying
system.
A. The
optional Calc-U-Dri is a revolutionary master control for
automatic, in-bin continuous flow grain drying. Calc-U-Dri
keeps grain moisture content no higher than 0.3% over set
point (percentage moisture desired). It also controls the
Grain Flow and take-away systems.
B. The Calc-U-Dri sensor, located
in the Grain Flow discharge tube, monitors all the grain leaving
the drying bin. Wall mounted monitors can never match Calc-U-Dri
sensor accuracy.
C. Model 84 Grain Flow features
a six or eight inch discharge auger with 700 bushel per hour
discharge capacity using dual floor augers.
D. With the addition of a Stir-Ator,
your bin becomes a wet holding tank with a capacity of up
to 16 feet deep, a continuous flow dryer of unmatched efficiency,
and a dry and store unit for the last bin full.
E. The optional Trans-Fer 700
pneumatic grain conveying system gives your system the added
flexibility needed for multi-bin operations.
DMC's
Standard: Grain Flow with Dry Grain Control DMC's
Dry Grain Control works like many systems by using air temperature
to determine grain dryness, automatically unloading your grain
when the air reaches the preselected temperature.
The
Dry Grain Control measures air temperature 12 to 18 inches
off the bin floor to determine when the grain is ready to
be discharged.
Model
84 Grain Flow Features & Benefits •
Exterior control box means your total drying system is operated
from one convenient location.
• Support feet move floor augers through grain at a smooth
even pace.
• Hood and floor auger design allows grain to be
evenly removed at up to 700 bushels per hour (limited only
by fan and heater drying capacity).
• Auger overload switch shuts down the entire system
should transfer equipment fail.
• Heavy duty construction of all components ensures long
life.
• Two-year (2) warranty on gear box and floor augers.
• Two (2) sensing systems.
Optional
Equipment for the Grain Flow •
Take-away auger control box
• Inclined transfer augers
• Discharge auger extensions
• Trans-Fer pneumatic conveying systems
• 8" x 15' or 18' vertical auger with accessories
• Bin-full switch to stop Grain Flow when storage bin
is full
• Single or three phase, 220V or 440V electrical options
• Vertical auger heads (two or three way) with chain
operated valve
• Grain Level Monitor
• Hard surfaced floor augers (rice only)
Model
84 Grain Flow Components
Control Box
The DMC Grain Flow with Calc-U-Dri is operated from a
control box located on the outside of the bin. Operating
lights and three contactor switches are located in the
box. These switches control auxiliary equipment, such
as take-away augers, and can be operated automatically
or manually for easy maintenance checks.
Rugged Gear Box
DMC's Gear Box is so tough that it is backed with a full
two (2) drying season warranty. The gear box features
timken tapered roller bearings, high temperature grease
seals and case hardened gears. Adjustable legs allow the
gear box to fit plenums from 12 to 20 inches.
Dual
Floor Augers
Grain Flow's gear box uses tough 1 1/4" case hardened
shafts to drive dual floor augers with hefty shafts and
heavy-duty flighting. These augers unload grain at up
to 700 bushel per hour (BPH) or 1500-2000 BPH using the
slide gate. Floor augers are covered by a full two (2)
drying season warranty. Unique
Improved Hood Design
Grain Flow's unique hood keeps grain from free-flowing
from the bin's center. There is no need for a resistor
ring or grain paddles that damage grain.
Power
System The
power system is located on the discharge end of the Grain
Flow to provide power directly to the gear box, thus simplifying
installation by virtually eliminating alignment adjustments.
This also provides for a left or right discharge option
for added flexibility. The motor's three belt drive ensures
no slip operation. A shift lever is conveniently located
to engage or disengage floor augers.
Grain
Flow Warranty:
The DMC Grain Flow is guaranteed for one drying season, to be
free of defects in material or workmanship, when properly installed
and operating in accordance with the instruction in the owner's
manual. Floor augers and gear boxes are guaranteed under identical
terms for 2 drying seasons. Warranty parts will be exchanged
F.O.B., Mason City, Iowa, without charge to the user. Damage
resulting from negligence voids the warranty. Warranty does
not include labor, installation or delivery of replacement parts.
Electric motors are covered by the warranty of the respective
manufacturers. The DMC Grain Flow warranty, and the liability
of DMC, its distributors, dealers and agents is limited to replacing,
without charge, all defective parts as outlined above. No other
warranties, expressed or implied, shall apply in any circumstances.
The manufacturer reserves the right to make changes in specifications
and price without incurring obligation on previously produced
merchandise.
